Autor Tema: No se me abre el cuadro de instalación de weewx  (Leído 35744 veces)

0 Usuarios y 1 Visitante están viendo este tema.

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #15 en: 30 de Noviembre del 2019, 13:21:15 pm »
A lo que me quería referir con lo de internet es que cuando ejecuto en el buscador o en la consola file:///var/www/html/weewx/index.html, me aparece que el archivo no existe

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #16 en: 30 de Noviembre del 2019, 15:31:43 pm »
A lo que me quería referir con lo de internet es que cuando ejecuto en el buscador o en la consola file:///var/www/html/weewx/index.html, me aparece que el archivo no existe

Has visto si tienes ese archivo index.html en la carpeta /var/www/html/weewx ?

Y eso no es subir nada a internet, es ver un archivo local por el navegador. Habrá que ver si weewx te está generando esos archivos en esa carpeta.

El resultado de service weewx status que has puesto es el típico cuando está leyendo el datalogger aunque es raro ya que dice que weewx lleva 13 horas funcionando...


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #17 en: 30 de Noviembre del 2019, 17:32:27 pm »
Sí, tengo ese archivo en la carpeta, y clicando en él ya se me ha abierto la página de internet de mis datos, gracias por la ayuda.
Pero por lo que veo, solo ha estado subiendo datos hasta la 1, y no se porqué

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #18 en: 30 de Noviembre del 2019, 17:33:32 pm »
Creía que era que subía los datos a internet, gracias por sacarme de mi confusión :;

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #19 en: 30 de Noviembre del 2019, 20:33:46 pm »
A ver, eso de hasta la 1... de este mediodía ? En la salida de service weewx status que has puesto antes eran las 13:14 en tu Raspberry y weewx estaba leyendo el datalogger de la Davis, siendo las 11:15 la última lectura/grabación a su base de datos, ignoro si seguiría después leyendo hasta las 13:15 que es la hora que dices tener en la página web de weewx.

Tendrás que ir comprobando con service weewx status que está leyendo/grabando registros de la Davis con la hora actualizada y si no, es que algo raro sucede.

En cuanto a lo de la página web con los datos puedes instalar apache2 en la raspi (sudo apt-get install apache2) y entrar en el navegador de la raspi a la dirección http://127.0.0.1/weewx/ o http://localhost/weewx/

Si le pones una IP local fija a la Raspi podrás acceder a esa página desde cualquier dispositivo de tu red local poniendo la IP local de la raspi.


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #20 en: 02 de Diciembre del 2019, 23:22:46 pm »
Hola, perdón por tardar en responder. Resulta que weewx si que genera imagenees y archivos, pero el copygenerator no los copia a /var/www/html/weewx. ¿Sabes por qué puede ser?

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #21 en: 02 de Diciembre del 2019, 23:31:11 pm »
Copia y pega el contenido de /etc/weewx/weewx.conf aquí


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #22 en: 03 de Diciembre del 2019, 00:38:19 am »
# WEEWX CONFIGURATION FILE
#
# Copyright (c) 2009-2019 Tom Keffer <tkeffer@gmail.com>
# See the file LICENSE.txt for your rights.

##############################################################################

# This section is for general configuration information.

# Set to 1 for extra debug info, otherwise comment it out or set to zero
debug = 0

# Root directory of the weewx data file hierarchy for this station
WEEWX_ROOT = /

# Whether to log successful operations
log_success = True

# Whether to log unsuccessful operations
log_failure = True

# How long to wait before timing out a socket (FTP, HTTP) connection
socket_timeout = 20

# Do not modify this. It is used when installing and updating weewx.
version = 3.9.2

##############################################################################

#   This section is for information about the station.

[Station]
   
    # Description of the station location
    location = La Manga del Mar Menor
   
    # Latitude and longitude in decimal degrees
    latitude = 37.64
    longitude = -0.71
   
    # Altitude of the station, with unit it is in. This is downloaded from
    # from the station if the hardware supports it.
    altitude = 5, meter
   
    # Set to type of station hardware. There must be a corresponding stanza
    # in this file with a 'driver' parameter indicating the driver to be used.
    station_type = Vantage
   
    # If you have a website, you may specify an URL
    #station_url = http://www.example.com
   
    # The start of the rain year (1=January; 10=October, etc.). This is
    # downloaded from the station if the hardware supports it.
    rain_year_start = 1
   
    # Start of week (0=Monday, 6=Sunday)
    week_start = 6

##############################################################################

[Vantage]
    # This section is for the Davis Vantage series of weather stations.
   
    # Connection type: serial or ethernet
    #  serial (the classic VantagePro)
    #  ethernet (the WeatherLinkIP or Serial-Ethernet bridge)
    type = serial
   
    # If the connection type is serial, a port must be specified:
    #   Debian, Ubuntu, Redhat, Fedora, and SuSE:
    #     /dev/ttyUSB0 is a common USB port name
    #     /dev/ttyS0   is a common serial port name
    #   BSD:
    #     /dev/cuaU0   is a common serial port name
    port = /dev/ttyUSB0
   
    # If the connection type is ethernet, an IP Address/hostname is required:
    host = 1.2.3.4
   
    ######################################################
    # The rest of this section rarely needs any attention.
    # You can safely leave it "as is."
    ######################################################
   
    # Serial baud rate (usually 19200)
    baudrate = 19200
   
    # TCP port (when using the WeatherLinkIP)
    tcp_port = 22222
   
    # TCP send delay (when using the WeatherLinkIP):
    tcp_send_delay = 0.5
   
    # The id of your ISS station (usually 1). If you use a wind meter connected
    # to a anemometer transmitter kit, use its id
    iss_id = 1
   
    # How long to wait for a response from the station before giving up (in
    # seconds; must be greater than 2)
    timeout = 4
   
    # How long to wait before trying again (in seconds)
    wait_before_retry = 1.2
   
    # How many times to try before giving up:
    max_tries = 4
   
    # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2
    model_type = 2
   
    # The driver to use:
    driver = weewx.drivers.vantage

##############################################################################

[Simulator]
    # This section is for the weewx weather station simulator
   
    # The time (in seconds) between LOOP packets.
    loop_interval = 2.5
   
    # The simulator mode can be either 'simulator' or 'generator'.
    # Real-time simulator. Sleep between each LOOP packet.
    mode = simulator
    # Generator.  Emit LOOP packets as fast as possible (useful for testing).
    #mode = generator
   
    # The start time. Format is YYYY-mm-ddTHH:MM. If not specified, the default
    # is to use the present time.
    #start = 2011-01-01T00:00
   
    # The driver to use:
    driver = weewx.drivers.simulator

##############################################################################

#   This section is for uploading data to Internet sites

[StdRESTful]
   
    [[StationRegistry]]
        # To register this weather station with weewx, set this to true
        register_this_station = false
   
    [[AWEKAS]]
        # This section is for configuring posts to AWEKAS.
       
        # If you wish to do this, set the option 'enable' to true,
        # and specify a username and password.
        # To guard against parsing errors, put the password in quotes.
        enable = false
        username = replace_me
        password = replace_me
   
    [[CWOP]]
        # This section is for configuring posts to CWOP.
       
        # If you wish to do this, set the option 'enable' to true,
        # and specify the station ID (e.g., CW1234).
        enable = false
        station = replace_me
   
    # If this is an APRS (radio amateur) station, uncomment
    # the following and replace with a passcode (e.g., 12345).
    #passcode = replace_me (APRS stations only)
   
    [[PWSweather]]
        # This section is for configuring posts to PWSweather.com.
       
        # If you wish to do this, set the option 'enable' to true,
        # and specify a station and password.
        # To guard against parsing errors, put the password in quotes.
        enable = false
        station = replace_me
        password = replace_me
   
    [[WOW]]
        # This section is for configuring posts to WOW.
       
        # If you wish to do this, set the option 'enable' to true,
        # and specify a station and password.
        # To guard against parsing errors, put the password in quotes.
        enable = false
        station = replace_me
        password = replace_me
   
    [[Wunderground]]
        # This section is for configuring posts to the Weather Underground.
       
        # If you wish to do this, set the option 'enable' to true,
        # and specify a station (e.g., 'KORHOODR3') and password.
        # To guard against parsing errors, put the password in quotes.
        enable = false
        station = replace_me
        password = replace_me
       
        # Set the following to True to have weewx use the WU "Rapidfire"
        # protocol. Not all hardware can support it. See the User's Guide.
        rapidfire = False

##############################################################################

#   This section specifies what reports, using which skins, to generate.

[StdReport]
   
    # Where the skins reside, relative to WEEWX_ROOT
    SKIN_ROOT = /etc/weewx/skins
   
    # Where the generated reports should go, relative to WEEWX_ROOT
    HTML_ROOT = /var/www/html/weewx
   
    # The database binding indicates which data should be used in reports.
    data_binding = wx_binding
   
    # Whether to log a successful operation
    log_success = True
   
    # Whether to log an unsuccessful operation
    log_failure = False
   
    # Each of the following subsections defines a report that will be run.
    # See the customizing guide to change the units, plot types and line
    # colors, modify the fonts, display additional sensor data, and other
    # customizations. Many of those changes can be made here by overriding
    # parameters, or by modifying templates within the skin itself.
   
    [[SeasonsReport]]
        # The SeasonsReport uses the 'Seasons' skin, which contains the
        # images, templates and plots for the report.
        skin = Seasons
        enable = true
   
    [[SmartphoneReport]]
        # The SmartphoneReport uses the 'Smartphone' skin, and the images and
        # files are placed in a dedicated subdirectory.
        skin = Smartphone
        enable = false
        HTML_ROOT = /var/www/html/weewx/smartphone
   
    [[MobileReport]]
        # The MobileReport uses the 'Mobile' skin, and the images and files
        # are placed in a dedicated subdirectory.
        skin = Mobile
        enable = false
        HTML_ROOT = /var/www/html/weewx/mobile
   
    [[StandardReport]]
        # This is the old "Standard" skin. By default, it is not enabled.
        skin = Standard
        enable = false
   
    [[FTP]]
        # FTP'ing the results to a webserver is treated as just another report,
        # albeit one with an unusual report generator!
        skin = Ftp
       
        # If you wish to use FTP, set "enable" to "true", then
        # fill out the next four lines.
        # Use quotes around passwords to guard against parsing errors.
        enable = false
        user = replace_me
        password = replace_me
        server = replace_me    # The ftp server name, e.g, www.myserver.org
        path = replace_me    # The destination directory, e.g., /weather
       
        # Set to True for an FTP over TLS (FTPS) connection. Not all servers
        # support this.
        secure_ftp = False
       
        # To upload files from something other than what HTML_ROOT is set
        # to above, specify a different HTML_ROOT here.
        #HTML_ROOT = /var/www/html/weewx
       
        # Most FTP servers use port 21
        port = 21
       
        # Set to 1 to use passive mode, zero for active mode
        passive = 1
   
    [[RSYNC]]
        # rsync'ing to a webserver is treated as just another report
        skin = Rsync
       
        # If you wish to use rsync, you must configure passwordless ssh using
        # public/private key authentication from the user account that weewx
        # runs to the user account on the remote machine where the files
        # will be copied.
        #
        # If you wish to use rsync, set "enable" to "true", then
        # fill out server, user, and path.
        # The server should appear in your .ssh/config file.
        # The user is the username used in the identity file.
        # The path is the destination directory, such as /var/www/html/weather.
        # Be sure that the user has write permissions on the destination!
        enable = false
        server = replace_me
        user = replace_me
        path = replace_me
       
        # To upload files from something other than what HTML_ROOT is set
        # to above, specify a different HTML_ROOT here.
        #HTML_ROOT = /var/www/html/weewx
       
        # Rsync can be configured to remove files from the remote server if
        # they don't exist under HTML_ROOT locally. USE WITH CAUTION: if you
        # make a mistake in the remote path, you could could unintentionally
        # cause unrelated files to be deleted. Set to 1 to enable remote file
        # deletion, zero to allow files to accumulate remotely.
        delete = 0
   
    ####
   
    # Various options for customizing your reports.
   
    [[Defaults]]
       
        [[[Units]]]
           
            # The following section sets what unit to use for each unit group.
            # NB: The unit is always in the singular. I.e., 'mile_per_hour',
            # NOT 'miles_per_hour'
            [[[[Groups]]]]
               
                group_altitude = meter    # Options are 'foot' or 'meter'
                group_degree_day = degree_C_day    # Options are 'degree_F_day' or 'degree_C_day'
                group_pressure = mbar    # Options are 'inHg', 'mmHg', 'mbar', or 'hPa'
                group_rain = mm    # Options are 'inch', 'cm', or 'mm'
                group_rainrate = mm_per_hour    # Options are 'inch_per_hour', 'cm_per_hour', or 'mm_per_hour'
                group_speed = meter_per_second    # Options are 'mile_per_hour', 'km_per_hour', 'knot', or 'meter_per_second'
                group_speed2 = meter_per_second2    # Options are 'mile_per_hour2', 'km_per_hour2', 'knot2', or 'meter_per_second2'
                group_temperature = degree_C    # Options are 'degree_F' or 'degree_C'
           
            # The following section sets the formatting for each type of unit.
            [[[[StringFormats]]]]
               
                centibar = %.0f
                cm = %.2f
                cm_per_hour = %.2f
                degree_C = %.1f
                degree_F = %.1f
                degree_compass = %.0f
                foot = %.0f
                hPa = %.1f
                hour = %.1f
                inHg = %.3f
                inch = %.2f
                inch_per_hour = %.2f
                km_per_hour = %.0f
                km_per_hour2 = %.1f
                knot = %.0f
                knot2 = %.1f
                mbar = %.1f
                meter = %.0f
                meter_per_second = %.1f
                meter_per_second2 = %.1f
                mile_per_hour = %.0f
                mile_per_hour2 = %.1f
                mm = %.1f
                mmHg = %.1f
                mm_per_hour = %.1f
                percent = %.0f
                second = %.0f
                uv_index = %.1f
                volt = %.1f
                watt_per_meter_squared = %.0f
                NONE = "   N/A"
           
            # The following section sets the label for each type of unit
            [[[[Labels]]]]
               
                day = " day", " days"
                hour = " hour", " hours"
                minute = " minute", " minutes"
                second = " second", " seconds"
                NONE = ""
           
            # The following section sets the format for each time scale.
            # The values below will work in every locale, but they may not look
            # particularly attractive.
            [[[[TimeFormats]]]]
               
                hour = %H:%M
                day = %X
                week = %X (%A)
                month = %x %X
                year = %x %X
                rainyear = %x %X
                current = %x %X
                ephem_day = %X
                ephem_year = %x %X
           
            [[[[Ordinates]]]]
               
                # Ordinal directions. The last one is for no wind direction
                directions = N, NNE, NE, ENE, E, ESE, SE, SSE, S, SSW, SW, WSW, W, WNW, NW, NNW, N/A
               
                # The following section sets the base temperatures used for the
                #  calculation of heating and cooling degree-days.

Desconectado gonchoCT

  • Jr. Member
  • **
  • Mensajes: 81
    • Ver Perfil
  • Estación: ESMUR3000000030380C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #23 en: 03 de Diciembre del 2019, 00:40:45 am »
  # Base temperature for heating days, with unit:
                    heating_base = 65, degree_F
                    # Base temperature for cooling days, with unit:
                    cooling_base = 65, degree_F
               
                # A trend takes a difference across a time period. The following
                # section sets the time period, and how big an error is allowed to
                # still be counted as the start or end of a period.
                [[[[[Trend]]]]]
                   
                    time_delta = 10800    # 3 hours
                    time_grace = 300    # 5 minutes
       
        # The labels to be used for each observation type
        [[[Labels]]]
           
            # Set to hemisphere abbreviations suitable for your location:
            hemispheres = N, S, E, W
           
            # Formats to be used for latitude whole degrees, longitude whole
            # degrees, and minutes:
            latlon_formats = %02d, %03d, %05.2f
           
            # Generic labels, keyed by an observation type.
            [[[[Generic]]]]
                barometer = Barometer
                dewpoint = Dew Point
                ET = ET
                heatindex = Heat Index
                inHumidity = Inside Humidity
                inTemp = Inside Temperature
                outHumidity = Humidity
                outTemp = Outside Temperature
                radiation = Radiation
                rain = Rain
                rainRate = Rain Rate
                UV = UV Index
                windDir = Wind Direction
                windGust = Gust Speed
                windGustDir = Gust Direction
                windSpeed = Wind Speed
                windchill = Wind Chill
                windgustvec = Gust Vector
                windvec = Wind Vector
                extraTemp1 = Temperature1
                extraTemp2 = Temperature2
                extraTemp3 = Temperature3
               
                # Sensor status indicators
               
                rxCheckPercent = Signal Quality
                txBatteryStatus = Transmitter Battery
                windBatteryStatus = Wind Battery
                rainBatteryStatus = Rain Battery
                outTempBatteryStatus = Outside Temperature Battery
                inTempBatteryStatus = Inside Temperature Battery
                consBatteryVoltage = Console Battery
                heatingVoltage = Heating Battery
                supplyVoltage = Supply Voltage
                referenceVoltage = Reference Voltage
       
        [[[Almanac]]]
           
            # The labels to be used for the phases of the moon:
            moon_phases = New, Waxing crescent, First quarter, Waxing gibbous, Full, Waning gibbous, Last quarter, Waning crescent

##############################################################################

#   This service acts as a filter, converting the unit system coming from
#   the hardware to a unit system in the database.

[StdConvert]
   
    # The target_unit affects only the unit system in the database. Once
    # chosen it cannot be changed without converting the entire database.
    # Modification of target_unit after starting weewx will result in
    # corrupt data - the database will contain a mix of US and METRIC data.
    #
    # The value of target_unit does not affect the unit system for
    # reporting - reports can display US, Metric, or any combination of units.
    #
    # In most cases, target_unit should be left as the default: US
    #
    # In particular, those migrating from a standard wview installation
    # should use US since that is what the wview database contains.
   
    # DO NOT MODIFY THIS VALUE UNLESS YOU KNOW WHAT YOU ARE DOING!
    target_unit = US    # Options are 'US', 'METRICWX', or 'METRIC'

##############################################################################

#   This section can adjust data using calibration expressions.

[StdCalibrate]
   
    [[Corrections]]
        # For each type, an arbitrary calibration expression can be given.
        # It should be in the units defined in the StdConvert section.
        # Example:
        foo = foo + 0.2

##############################################################################

#   This section is for quality control checks. If units are not specified,
#   values must be in the units defined in the StdConvert section.

[StdQC]
   
    [[MinMax]]
        barometer = 26, 32.5, inHg
        pressure = 24, 34.5, inHg
        outTemp = -40, 120, degree_F
        inTemp = 10, 120, degree_F
        outHumidity = 0, 100
        inHumidity = 0, 100
        windSpeed = 0, 120, mile_per_hour
        rain = 0, 10, inch

##############################################################################

#   This section controls the origin of derived values.

[StdWXCalculate]
   
    [[Calculations]]
        # How to calculate derived quantities.  Possible values are:
        #  hardware        - use the value provided by hardware
        #  software        - use the value calculated by weewx
        #  prefer_hardware - use value provide by hardware if available,
        #                      otherwise use value calculated by weewx
       
        pressure = prefer_hardware
        barometer = prefer_hardware
        altimeter = prefer_hardware
        windchill = prefer_hardware
        heatindex = prefer_hardware
        dewpoint = prefer_hardware
        inDewpoint = prefer_hardware
        rainRate = prefer_hardware

##############################################################################

#   For hardware that supports it, this section controls how often the
#   onboard clock gets updated.

[StdTimeSynch]
   
    # How often to check the weather station clock for drift (in seconds)
    clock_check = 14400
   
    # How much it can drift before we will correct it (in seconds)
    max_drift = 5

##############################################################################

#   This section is for configuring the archive service.

[StdArchive]
   
    # If the station hardware supports data logging then the archive interval
    # will be downloaded from the station. Otherwise, specify it (in seconds).
    archive_interval = 300
   
    # If possible, new archive records are downloaded from the station
    # hardware. If the hardware does not support this, then new archive
    # records will be generated in software.
    # Set the following to "software" to force software record generation.
    record_generation = hardware
   
    # Whether to include LOOP data in hi/low statistics
    loop_hilo = True
   
    # The data binding used to save archive records
    data_binding = wx_binding

##############################################################################

#   This section binds a data store to a database.

[DataBindings]
   
    [[wx_binding]]
        # The database must match one of the sections in [Databases].
        # This is likely to be the only option you would want to change.
        database = archive_sqlite
        # The name of the table within the database
        table_name = archive
        # The manager handles aggregation of data for historical summaries
        manager = weewx.wxmanager.WXDaySummaryManager
        # The schema defines the structure of the database.
        # It is *only* used when the database is created.
        schema = schemas.wview.schema

##############################################################################

#   This section defines various databases.

[Databases]
   
    # A SQLite database is simply a single file
    [[archive_sqlite]]
        database_name = weewx.sdb
        database_type = SQLite
   
    # MySQL
    [[archive_mysql]]
        database_name = weewx
        database_type = MySQL

##############################################################################

#   This section defines defaults for the different types of databases.

[DatabaseTypes]
   
    # Defaults for SQLite databases
    [[SQLite]]
        driver = weedb.sqlite
        # Directory in which the database files are located
        SQLITE_ROOT = /var/lib/weewx
   
    # Defaults for MySQL databases
    [[MySQL]]
        driver = weedb.mysql
        # The host where the database is located
        host = localhost
        # The user name for logging in to the host
        user = weewx
        # The password for the user name (quotes guard against parsing errors)
        password = weewx

##############################################################################

#   This section configures the internal weewx engine.

[Engine]
   
    [[Services]]
        # This section specifies the services that should be run. They are
        # grouped by type, and the order of services within each group
        # determines the order in which the services will be run.
        prep_services = weewx.engine.StdTimeSynch
        data_services = ,
        process_services = weewx.engine.StdConvert, weewx.engine.StdCalibrate, weewx.engine.StdQC, weewx.wxservices.StdWXCalculate
        archive_services = weewx.engine.StdArchive
        restful_services = weewx.restx.StdStationRegistry, weewx.restx.StdWunderground, weewx.restx.StdPWSweather, weewx.restx.StdCWOP, weewx.restx.StdWOW, weewx.restx.StdAWEKAS
        report_services = weewx.engine.StdPrint, weewx.engine.StdReport

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #24 en: 03 de Diciembre del 2019, 08:36:16 am »
Veamos, alguna cosa hay que cambiar...

En week_start = 6 pon 0 en vez de 6 si quieres que la semana empieza por lunes y no domingo.

En la sección [[[[Groups]]]] pon en las unidades de viento km_per_hour en vez de meter_per_second o si no se generará todo en m/s.

En la sección [StdConvert] tienes target_unit = US y eso significa que estará grabando los valores en formato imperial en la base de datos por lo que por ejemplo los grados los grabará en Farenheit en vez de Celsius.

No me di cuenta de advertírtelo cuando empezaste y no influye en cómo weewx da la salida de los valores, pero sí es un inconveniente para los que nos movemos sólo con el formato métrico el arreglar valores en una base de datos con ese otro formato.

La solución por desgracia sería borrar base de datos y empezar con target_unit = METRIC
Sería volver a empezar de 0 con los datos. Ahora que llevas pocos sería lo menos traumático.

En cuanto a lo de la web de weewx… parece ser que en las últimas versiones de weewx ya no es Standard el skin que viene activado por defecto y es el Seasons. Sería en su skin.conf (/etc/weewx/skins/Seasons/skin.conf) donde habría que configurar la plantilla de meteoclimatic y mover la plantilla meteoclimatic.htm.tmpl del skin Standard al Seasons.

Los archivos weewx de Windows deberían de estar actualizándose en /var/www/HTML/weewx/

Sale desactualizado el archivo index.html ??


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #25 en: 03 de Diciembre del 2019, 08:39:41 am »
Por cierto.... cuando se cambia algo en el weewx.conf hay que reiniciar weewx con sudo service weewx restart para que los cambios surtan efecto.


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado Rubendgl

  • Jr. Member
  • **
  • Mensajes: 62
    • Ver Perfil
    • MeteoNigran
  • Estación: ESGAL3600000036350C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #26 en: 03 de Diciembre del 2019, 11:38:30 am »
Perdón por la intromisión en este hilo pero justamente eso me está pasando a mi ahora.
Ahora, desde que borré el dataloger graba los registros nuevos y se actualiza la base de datos.
Genera archivos pero no los copia a /var/www/html/weewx.
Yo desactivé en skin seasons y activé el standard, que es donde tengo todo.
La web lo muestra correctamente pero sigue a fecha de 1/12/2019  21:15
  :;

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #27 en: 03 de Diciembre del 2019, 14:45:39 pm »
A ver, cuando ocurren estas cosas primeramente hay que mirar si se está generando el archivo index.html del skin en su carpeta correspondiente con ls -l

Si está actualizada la fecha del fichero es que weewx lo está generando pero si no están actualizados los datos en su interior hay que ver el log de weewx o el del sistema para ver si da alguna pista.

Se puede poner en el weewx.conf el debug en nivel 1 y dará más información.

En la web de weewx salen unas pautas a seguir:

http://www.weewx.com/docs/usersguide.htm#html_generated_but_not_updated

Como se ve tiene que ver con algún registro de tiempo mal en cuanto a hora o de la Raspi misma.

Repito que ver el log nos dará más pistas de si hay un error y poder buscar sobre él por google.


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es

Desconectado Rubendgl

  • Jr. Member
  • **
  • Mensajes: 62
    • Ver Perfil
    • MeteoNigran
  • Estación: ESGAL3600000036350C
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #28 en: 03 de Diciembre del 2019, 22:32:55 pm »
En mi caso, despues de borrar la memoria del dataloger, como se explica lo siguiente: ??

1.- Graba los registros a la base de datos

dic 03 21:20:15 raspberrypi weewx[322]: manager: Added record 2019-12-03 21:20:00 UTC (1575408000) to database 'weewx.sdb'
dic 03 21:20:15 raspberrypi weewx[322]: manager: Added record 2019-12-03 21:20:00 UTC (1575408000) to daily summary in 'weewx.sdb'
dic 03 21:25:15 raspberrypi weewx[322]: manager: Added record 2019-12-03 21:25:00 UTC (1575408300) to database 'weewx.sdb'
dic 03 21:25:15 raspberrypi weewx[322]: manager: Added record 2019-12-03 21:25:00 UTC (1575408300) to daily summary in 'weewx.sdb'

2.- No actualiza nada de la carpeta /var/www/html/weewx

-rw-r--r-- 1 root root 14039 dic  2 21:33 index.html

3-. La base de datos se graba correctamente

-rw-r--r-- 1 root root 897024 dic  3 21:25 weewx.sdb

PD:
    Me acabo de dar cuenta ahora mismo que los datos que envia a Awekas y Wunderground, se actualizan correctamente y la estación está online.
Solo falla la generación de la web.
« Última modificación: 03 de Diciembre del 2019, 23:03:38 pm por Rubendgl »

Desconectado jmviper

  • Investigación
  • Hero Member
  • ******
  • Mensajes: 4.403
  • "Vortex Complex"
    • Ver Perfil
    • www.meteoarchena.es
  • Estación: Archena - ESMUR3000000030600B
Re:No se me abre el cuadro de instalación de weewx
« Respuesta #29 en: 03 de Diciembre del 2019, 23:35:42 pm »
Puedes poner la sección [StdReport] hasta la sección FTP (no la incluyas) ?

Pon también el resultado de ejecutar pip list


Archena, Valle de Ricote (Murcia). 120 msnm. 19.622 hab.
Davis Vantage Pro2 Plus

www.meteoarchena.es